Aquamaster C800 Pro – pH and EC Controller for Automatic Nutrient Solution Dosing
Aquamaster C800 Pro – pH and EC Controller for Automatic Nutrient Solution Dosing
-
Parameters: pH 0-14, EC and temperature 0-50 °C
-
Protection: IP63, power supply 50-60 Hz
-
Standard: Includes pH and EC electrodes and adapter
-
Inline: pH ±0.01, TDS 0-19990 ppm, 2 or 3-point calibration
-
Compatible pumps: C10, C20 and C30 via UTP cable
-
Spare parts: Electrodes not available separately
Discover the benefits of the PRO CLUB
Discounts of up to -12%, priority shipping and more.
Easy returns within 15 days
No questions asked
Description
- 🔌 Automatic dosing: Corrects pH and EC without intervention.
- 🧪 Continuous measurement: pH 0-14, EC and temperature 0-50 °C, IP63.
- ⚙️ Inline Version: pH accuracy of ±0.01 and 3-point calibration.
- 🔄 No loose replacement: Includes factory electrodes but they are not sold separately.
Connects via UTP to the C10, C20 and C30 pumps: start with pH and then expand.
Full description
The C800 Pro is Aquamaster's nutrient controller: a panel-mounted device that continuously measures pH, EC, and temperature and controls the dosing pumps to maintain the solution at your programmed values. Stop correcting the reservoir yourself three times a day.
pH range 0-14 and temperature 0 to 50 °C, with IP63 protection and 50-60 Hz power supply. It connects to the C10, C20, and C30 dosing pumps via UTP cable, so you can start with a single pH pump and expand to nutrients later.
Standard or Inline
Standard C800 Pro: measures by probe immersion in the reservoir. Includes pH and EC electrodes and the adapter from the factory. Our supplier provides them upon request.
C800 Pro Inline: measures in-line, with the probes installed inside the piping, and is significantly more accurate in pH (±0.01 compared to the standard version). Adds TDS reading from 0 to 19990 ppm and 2- or 3-point digital calibration. It is the option for closed-loop installations where you want to control the water that actually goes to the plant, not the water in the tank.
Important notice about spare parts
The C800 Pro comes with its electrodes from the factory, but our distributor does not sell them separately. The Aquamaster replacement electrodes in our catalog correspond to the previous generation of handheld meters and are not compatible with this controller.
We say this because in a controller that works 24 hours a day, the electrode wears out sooner than in a handheld meter. If this is a critical point for your installation, consult us beforehand and we will manage the spare part request directly with the manufacturer.
No product image: our supplier does not publish a clean photograph of this equipment. They do provide the technical manual in PDF; write to us and we will send it to you.
Warranty
At GrowIndustry we only work with proven quality products and trusted brands.
Every item goes through a check before shipping to make sure it arrives in perfect condition and ready to use.
Your satisfaction is our priority.
How to use
1. Mount the controller on a wall in a dry and accessible area.
2. Install the probes by immersion or in the piping, depending on the version.
3. Connect the dosing pumps to the controller using a UTP cable.
4. Calibrate pH and EC with standard solutions before putting it into service.
5. Program the pH and EC setpoints for the growing phase.
6. Check the calibration every 2 to 4 weeks and clean the probes.

Aquamaster C800 Pro – pH and EC Controller for Automatic Nutrient Solution Dosing
Join our exclusive club for regular customers and start enjoying unbeatable prices, VIP service and premium support for your grows.
Increasing discounts
Save an extra -3% to -12%
Free shipping before
From €39 for Bronze and no minimum for Platinum (up to 10 kg)
Fast deliveries
With free, discreet shipping
Extended warranty
Up to 3 years
Frequently asked questions
-
It is a panel-mounted nutrient controller that measures pH, EC and temperature continuously and drives the dosing pumps to keep the solution at the values you set. You stop being the one correcting the reservoir several times a day.
-
The standard one measures by immersing the probe in the reservoir and comes with the pH and EC electrodes and the adapter as standard. The Inline one measures inside the pipe, is noticeably more accurate on pH at ±0.01, and adds a TDS reading from 0 to 19990 ppm plus digital 2- or 3-point calibration.
-
It connects to the C10, C20 and C30 dosing pumps using a UTP cable. That lets you start with just a pH pump and expand later to nutrient dosing.
-
We will be straight with you: the unit comes with its electrodes from the factory, but our distributor does not sell them separately, and the Aquamaster electrodes in our catalogue belong to the handheld meters of the previous range and do not fit this controller. If that is a critical point for you, ask us first and we will request the spare from the manufacturer.
-
It works with a pH range of 0 to 14 and a temperature range of 0 to 50 degrees, with IP63 protection and a 50-60 Hz supply. It is a panel unit designed to run continuously in the installation.
-
Our supplier does not publish a clean photograph of this unit, which is why the listing appears without an image. They do provide the technical manual as a PDF: write to us and we will send it over so you can look it through before deciding.