Blumat Easy – Automatic capillary irrigation with a plastic bottle

Blumat Easy – Automatic capillary watering with a plastic bottle

Blumat Easy is a porous ceramic cone with a threaded adapter that fits directly onto an empty plastic bottle between 0.25 and 2 liters. The cone is buried in the substrate and lets through more or less water depending on the soil moisture, so the plant receives only what it needs, without electricity, without a pump and without a timer. It is the simplest and most economical option from the Austrian brand Blumat to solve a "I'm going away for 10 days" without setting up any installation.

⚠️ Available to order: the "1 unit" variant is available to order; check the lead time before buying.

Key features

• Capillary watering: the ceramic cone regulates the flow of water depending on the moisture of the substrate, without electricity or a pump.
• Fits a bottle: threaded adapter for plastic bottles from 0.25 to 2 liters; you provide the container.
• Two flow rates: Blumat Easy delivers up to 200 ml per day and Blumat Easy XL up to 300 ml per day.
• Self-contained and no installation: it does not need tubes, a tap, or an elevated container; each unit works on its own.
• Austrian manufacturing: Blumat ceramic, the same technology as the Tropf-Blumat system.

How to use it

Submerge the ceramic cone in water until it is completely saturated. Fill a plastic bottle of 0.25 to 2 liters with water and make a little hole in the bottom of the bottle so that air can enter: without that breather, the water will not flow down. Screw the Blumat Easy adapter onto the mouth of the bottle, turn it upside down and bury the cone in the substrate next to the plant, leaving the bottle resting or secured upside down. From then on, the cone takes care of itself: when the substrate dries out, it lets water through; when it is moist, it cuts it off.

Place one cone per plant. The radius of action of the cone is approximately 20-25 cm around the point where it is buried.

What is it compatible with?

Blumat Easy DOES NOT connect to the Tropf-Blumat system. It is a self-contained product: it does not accept an Ø8 mm tube or a Ø3 mm feeder, it cannot be plugged into a pressure reducer or a container connector. Its only "water source" is the plastic bottle you screw onto it.

Remember that the Tropf-Blumat modular system works with two proprietary diameters that are not interchangeable: the Ø8 mm is the supply line (the main pipe that carries the water) and the Ø3 mm is the feeder that goes from the line to the sensor. Neither of them fits the Blumat Easy. If what you want is a fixed installation connected to a tap or a container, you need the Tropf-Blumat sensors, not this product.

Technical specifications

• Brand: Blumat (Austria)
• Type: capillary watering cone with bottle adapter
• Supported bottles: plastic, from 0.25 to 2 liters
• Blumat Easy flow rate: up to 200 ml/day
• Blumat Easy XL flow rate: up to 300 ml/day
• Radius of action: 20-25 cm per cone
• Coverage: 1 cone per plant
• Power supply: does not need electricity or a pump
• Compatibility: cannot be connected to the Tropf-Blumat system
• Formats: blister pack of 3 units · 1 unit (available to order) · XL blister pack of 2 units

At GrowIndustry we only work with proven quality products and trusted brands.

Every item goes through a check before shipping to make sure it arrives in perfect condition and ready to use.

Your satisfaction is our priority.

1. Submerge the ceramic cone in water until it is completely saturated.
2. Fill a plastic bottle with between 0.25 and 2 liters of water.
3. Poke a small hole in the bottom of the bottle to allow air to enter.
4. Screw the Blumat Easy adapter into the mouth of the bottle and tighten it well.
5. Turn the assembly upside down and bury the cone in the substrate next to the plant.
6. Support or secure the bottle upside down and check the water level every few days.